How to Winterize Drafty Windows

With winter rapidly approaching, it's time to seal drafty windows to prevent cold winds from blowing into your home. And while there are many ways to solve this problem, the best approach requires a two-pronged attack: caulking around the outside of the window and weatherstripping the inside.

CAULKING

Begin by using a stiff-blade putty knife to scrape off any old caulk or peeling paint from around the exterior perimeter of the window. Then, clean away all dirt and dust using a scrub brush dipped in warm, soapy water. Wipe the surfaces dry with a clean cloth.

Next, apply a fresh bead of caulk around the outside perimeter of the window, creating a continuous wind-blocking seal between the window frame and siding. Be sure to use an exterior-grade caulk. I recommend either 100 percent silicone sealant or a "siliconized" acrylic caulk. Both adhere well and will remain flexible for years.

WEATHERSTRIPPING

After caulking around the outside of the window, move inside and use weatherstripping to seal around the sash. (The sashes are the movable parts of a window that open and close.) There are dozens of different styles of weatherstripping available for sealing windows, but these are top five types:

Adhesive-backed foam: This is a compression type of weatherstripping, meaning that when the window closes against it, the foam compresses to seal gaps and block drafts. It features easy peel-and-stick application and cuts easily with scissors. Just be sure to thoroughly clean the area around the inside of the window, as the adhesive won't stick to dusty, dirty surfaces.

On double-hung windows, apply adhesive-backed foam weatherstripping to the bottom edge of the lower sash, and to the top edge of the upper sash. If you don't want to apply the weatherstripping to the sash, stick it to the sill directly below the lower sash, and to the head jamb above the upper sash. Either way, once the sash is closed and locked, the foam will seal out drafts. On sliding or casement windows, apply the adhesive-backed foam to the vertical edge of the sash or vertically along the side jamb.

Tubular rubber-gasket weatherstripping: This is similar to adhesive-backed foam, except that it's formed into a hollow rubber tube instead of dense foam. When compressed by the sash, the tubular weatherstripping conforms to space, effectively sealing out drafts. Some tubular gaskets have peel-and-stick adhesive backing, while others have an attached metal or wood flange that must be secured with nails or screws. Also look for foam-filled tubular gaskets that have a spongy-foam core, which holds its shape better than the hollow-core gaskets.

Spring V-Seal: This is a resilient polypropylene plastic or metal strip that comes folded into a V-shape. It's known as tension-seal weatherstripping because of the V-shape springs open, creating tension between the sash and window frame that blocks the passage of air. Plastic V-seal can be cut with scissors, but you'll need aviation snips to cut metal V-seal, which comes in copper, aluminium, bronze, and stainless steel. Also, the plastic type often has a peel-and-stick backing, while metal V-seal must be nailed in place.

V-seal can be installed vertically along the sides of double-hung windows, and at the horizontal meeting rail where the two sashes meet when closed. On casement or sliding windows, V-seal is installed along the vertical side jamb where the sash closes.

Felt: Felt is one of the oldest types of weatherstripping. It's commonly sold in rolls with or without an adhesive backing and is also available with an attached metal mounting flange. Felt is used as a compression weatherstripping around the inside of double-hung, casement, and sliding windows. Felt is affordable and easy to install, but it doesn't last as long as other types of weatherstripping and must be replaced every two to four years.

Window insulation kits: These kits block cold air by sealing the entire window behind a large sheet of shrink-wrap plastic. The plastic adheres to the interior window casing with double-sided tape; you then use a blow dryer to seal it in place. Window insulation kits are very effective at sealing out drafts, but keep in mind that you won't be able to open the window until next spring when you peel off the plastic wrap.

Here's one final tip for sealing drafty double-hung windows. Most of them have a single sash lock installed at the horizontal meeting rails where the upper and lower sash meet. To ensure that the two sashes fit tightly together, add a second sash lock: Unscrew the existing sash lock and reinstall it about one-third of the way in from the side jamb. For example, if the window is 24 inches wide, move the sash lock from the middle of the sash to about 8 inches from the end. Next, buy a second sash lock and install it 8 inches in from the opposite side jamb. Now, when you engage both locks, the sashes will fit together tightly.

Resources: popularmechanics.com